GearReg Calibration

Calibration register for tools and instruments

Keep every calibration certificate, due date and lab in one place, and know what is away being calibrated. Torque wrenches, gas detectors, multimeters, load cells and pressure gauges.

How an instrument goes on the register

The same steps as the rigging and test and tag registers, ending with the calibration certificate.

  1. Scan the QR tag

    If tagged

    A new tag adds the item to the register. A known tag brings up the item, and you still take the item and serial photos to confirm it is the right gear.

  2. Photo of the item

    The whole item, so the record shows what it looked like.

  3. Photo of the serial

    The AI reads the serial number from the label.

  4. Photo of the model plate

    The AI reads the make, model and dates, and suggests a category.

  5. Certificate

    If available

    Upload the calibration certificate, if you have it. A PDF or a photo is fine.

A competent person decides pass or fail. The AI reads labels and fills in the form; it never makes the decision.

No GearReg tags yet? Scan the QR tags already on your gear (any QR code works), or an administrator can print a sheet of tags from the app. GearReg printed QR tags will be on sale after the trial.

Instruments the calibration register is set up for

Each instrument type has a short checklist for when a calibration is recorded.

CategoryWhat is checked
Torque wrench / toolInstrument clean, undamaged and complete. Identification / serial number legible. Calibration certificate checked: correct instrument, range and results.
Gas detectorInstrument clean, undamaged and complete. Identification / serial number legible. Calibration certificate checked: correct instrument, range and results. Bump test passed before use.
Multimeter / electrical test instrumentInstrument clean, undamaged and complete. Identification / serial number legible. Calibration certificate checked: correct instrument, range and results. Leads and probes undamaged.
Load cell / dynamometerInstrument clean, undamaged and complete. Identification / serial number legible. Calibration certificate checked: correct instrument, range and results.
Pressure gaugeInstrument clean, undamaged and complete. Identification / serial number legible. Calibration certificate checked: correct instrument, range and results.
Other calibrated instrumentInstrument clean, undamaged and complete. Identification / serial number legible. Calibration certificate checked: correct instrument, range and results.

These are the categories every new company starts with. Rename them, add your own and edit any checklist.

Your lab calibrates. A person checks the record.

GearReg does not calibrate anything. Your calibration lab does, and GearReg keeps the certificate, the result and the due date with the instrument.

The AI reads labels and suggests a category. What the AI does and does not do.

  • The certificate checkedA person confirms the certificate is for the right instrument, range and results.
  • Out of toleranceAn instrument that fails calibration goes on the out of service register, with a reminder to review work done with it since its last good calibration.
  • Lab and certificate numberRecorded with each calibration, with the result.

Due dates and gear away at the lab

See what is due, what is overdue and what is away being calibrated.

  • Due datesTaken from the certificate's own due date when it gives one. Otherwise 12 months from the calibration date, or 6 months if you choose.
  • Send for calibrationMark an instrument as away at the lab, so nobody goes looking for it, until the new calibration is recorded.
  • Certificates with the instrumentThe certificate PDF or photo stays on the instrument's record.

Calibration reports for audits

PDF, Excel and CSV exports with your logo. They list the lab and the certificate number, and the Excel and CSV files link to each certificate.

  • Three reportsThe instrument register, the calibration history and the out of service register.
  • Certificates linkedEach calibration row links to its certificate file in Excel and CSV.

Sample coming. A sample calibration export made with demo data will be added here. Until then, see the rigging and height safety samples for the layout.

Calibration register: questions

Does GearReg calibrate my instruments?
No. Your calibration lab does. GearReg keeps the certificate, the result and the due date with the instrument.
What happens when an instrument is out of tolerance?
It goes on the out of service register, with a reminder to review work done with it since its last good calibration.
How is the due date set?
From the certificate's own due date when it gives one. Otherwise it is 12 months from the calibration date, or 6 months if you choose.
Does the AI read the certificate?
You enter the lab, the certificate number and the result. The AI reads the serial and model labels on the instrument.
What does it cost?
Free during the trial. Pricing will be published before anything is charged.